Diamond Cutting Tools | Diamond drill bits | Diamond Cutting Wheels | Marble Blades | Stone Cutting Tools | Diamond Tool Manufacturers

ask your question here

AskHeader

Name:	*
Email:
Subject:	*
Question: *
Enter the code exactly as you see it in the image:- (cookies must be enabled) Load New Code *

ask an expert

I see the step 1 & 2 grinders for the Park Pro-edge, what are the part#'s for step 3,4 and 5? Thanks

Submitted By: KEN KRUGER 12/03/2009 07:48 AM

Position       Item #
    3              FP-3
    4              FP-4
    5              FP-5

We use a pro edge 2 for all straight polishing. We really like the alpha hard resin pads for polishing straight runs and seams. It is very hard to get these pads now and we are considering switching to terminator pads. We prefer a 4". Do you recommend any pad in particular? We have always liked the terminator products and hope to do business again in the near future. Thanks Andy Ottobre

Submitted By: Andy Ottobre 09/20/2009 01:10 PM

Andy,

For flat edge/seam clean for the pro edge we recommend using first the Terminator Zoom Cup Wheels for Flats followed up by the Terminator Rigid Snail Lock Polishers (see links below).

http://www.continentaldia.com/c-114-terminator-zoom-cup-wheels-for-flat-polish.aspx

http://www.continentaldia.com/c-116-terminator-rigid-snail-lock-polishers.aspx

The cup wheels are great for removing saw marks and truing up the stone while the rigid polishers give a nice flat even polish. Please give us call if you have any other further questions.

Best Regards.

Will one of your diamond drill bits core a hole through china/porcelin cups and saucers. Some success using drill bit from Lowes/Home Depot, but they won't go through certain ones. Must be a harder density material.

Submitted By: Dick Davis 11/03/2009 05:36 PM

Yes just be sure to use plenty of water, you can burn bits real quick on porcelain. The ones I would recommend are the Art. series, links are below.

http://www.continentaldia.com/c-142-terminator-continous-thin-wall-core-bits.aspx

or

http://www.continentaldia.com/c-233-terminator-blind-hole-bits.aspx

Regards

Dear Sir, I need polishing pads for my park single head Pro-egde 3 polisher I need tooling to do Full round edges/half round edges and flat edges for Full Round and half/round edges I need Diamond toolings as well the attachment in Snail Lock. Can you please recomend me the tooling pads which I can do the 3 different edges with same pads. Thanks kind regards Mark Cross

Submitted By: Mark Cross 09/10/2009 09:28 AM

Hi Mark,

Below I have attached a link for our Terminator 5 Step System products, this system will work for all radius type or radius to flat edges.

http://www.continentaldia.com/c-91-terminator-5-step-system.aspx

When doing radius edges the surface of the tooling tends to de-shape meaning the surface of the tool doesn't remain truely flat. So to get the best finish on flat edges we recommend separate tooling solely for flat polishing, I have attached the following links for those tools:

http://www.continentaldia.com/c-114-terminator-zoom-cup-wheels-for-flat-polish.aspx

http://www.continentaldia.com/c-116-terminator-rigid-snail-lock-polishers.aspx

Take a look and if you have any further questions please give us a call 800-595-1237.

Thanks for the question.

Best regards.

Is the CRBP410 blade for regular "Target" wet saws?

Submitted By: Sam Fleming 04/22/2009 05:23 AM

Yes they are made for tile saws. One thing to check is the arbor fitting on your saw, in the 10" there are two different arbor choices; either a diamond knockout to 5/8" arbor (Item code CRBP410) or a 30mm to 1" arbor (Item code CRBP410/1A).

Best,

Seb

i have slabs of marble with a high content of iron , the terminator marble blade glazez over and runs real slow , is there a blade that would work better to get the cutting speeds back up ?

Submitted By: steven wright 09/18/2009 12:41 PM

I would suggest either the Terminator Zoom16 or Zoom25. However being that the material contains a lot of iron you don't want to push the blade too hard, and be sure there is plenty of water directed at the cutting area.

need cove dupont and waterfall edge profile bits - do yall have in stock - need info

Submitted By: travie nail 08/20/2009 06:58 AM

Yes we do give our sales office a call 1.800.595.1237 and talk to one of our sales reps. and he/she can help you.

Best regards.

What is the speed and rpm for this tool

Submitted By: Mark Eudy 04/22/2009 09:57 PM

CW100: Terminator CNC Gauging/Stubbing Wheel

RPM: 4500-5000

Feed Rate: Depending on the material and how much you are removing it varies. Generally at a 1/16" removal the feed is between 30-40in/min.

*Important to note that only half the diameter (2") of the tool should be working at given time. If you try and run the full 4" of the tool it will bog down and not work properly.

Best,

Seb

Will the router bits Terminator Xtreme Ogee 3/4" (2CM) Pos. 1 & 2 fit a Master 3000? As will any of the other Terminator router bits?

Submitted By: Debra 05/29/2009 09:05 AM

Yes all our router bits come with both a M8 and M10 bolt. Generally speaking the standard bolt size on most routers is M10 which I believe the Master is.

Hello, What is your return policy? Thanks, NN

Submitted By: Nick Nikolaev 06/04/2009 12:14 PM

Please view the link:

Return Policy

How can I get a catalog?

Submitted By: Rebecca 06/16/2009 08:28 AM

Please email your company information to sales@continentaldia.com and we will get one out you.

I have ctrs16-2 terminator blade with 4 teeth off can you fix it

Submitted By: MARK BEAUCHAMP 07/09/2009 09:24 AM

We would need to inspect the blade first. Please send your blade back to the below address in a well packaged box with your contact information and we will get back to you.

Continental DIA Diamond Products, Inc.
1300 Industrial Road, Ste. #18
San Carlos, CA 94070-4130

Best Regards.